Mechanical and Physical Properties of Binderless Particleboard from Rice Straw and Banana Pseudostem

Main Article Content

Nutnaree Saropas
Prapaporn Huijisut
Sorada Noratad
Sureepan Supansomboon
Panitan Wanakamol
Supitcha Supansomboon

Abstract

The commercial particleboards used nowadays are manufactured with synthetic adhesives containing formaldehyde which is considered harmful to health and has a negative impact on the environment. A binderless particleboard fabricated from agricultural waste materials can solve these issues. This research explored the feasibility of using rice straw and banana pseudostem to produce binderless particleboard. The optimal preparation conditions for production were carried out using the ratios of rice straw to banana pseudostem at 100:0, 75:25, 50:50, 25:75 and 0:100, the pressing temperatures of 140°C, 160°C, and 180°C, and the compression times of 10 and 30 min. The physical and mechanical properties of the particleboard including density, moisture content, thickness swelling, modulus of rupture and modulus of elasticity were investigated. Morphological analysis was studied by scanning electron microscopy. It was found that it was possible to produce binderless particleboard from rice straw and banana pseudostem using a hot press method. The results showed that a higher content of banana pseudostem led to good mechanical properties and adhesion with lower thickness swelling. Cross-section of the binderless particleboards revealed that banana pseudostem acted as a binder.  Fourier transform infrared spectroscopy (FTIR) also confirmed the occurrence of self-bonding in these binderless particleboards. The optimum preparation conditions were achieved with the ratio of rice straw to banana pseudostem of 0:100, and a pressing temperature of 180°C for 30 min. The modulus of rupture (MOR) and modulus of elasticity (MOE) were approximately 12 MPa and 1800 MPa, respectively. This binderless particleboard is a potential candidate for use in green buildings.

Article Details

Section
Original Research Articles

References

Anglès, M. N., Ferrando, F., Farriol, X. & Salvadó, J. (2001). Suitability of steam exploded residual softwood for the production of binderless panels. Effect of the pre-treatment severity and lignin addition. Biomass and Bioenergy, 21(3), 211-224. https://doi.org/10.1016/S0961-9534(01)00031-9

Astari, L., Sudarmanto, & Akbar, F. (2019). Characteristics of particleboards made from agricultural wastes. IOP Conference Series: Earth and Environmental Science, 359(1), Article 012014. https://doi.org/10.1088/1755-1315/359/1/012014

Badanayak, P., Jose, S., & Bose G. (2023). Banana pseudostem fiber: A critical review on fiber extraction, characterization, and surface modification. Journal of Natural Fibers, 20(1), Article 2168821. https://doi.org/10.1080/15440478.2023.2168821

Bardak, S., Nemli, G., & Bardak, T. (2019). The quality comparison of particleboards produced from heartwood and sapwood of European larch. Maderas. Ciencia y Tecnología, 21(4), 511-520.

Barragȧn-Lucas, A. D., Llerena-Miranda, C., Quijano-Avilés, M. F., Chóez-Guaranda, I.A., L. Maldonado-Guerrero, L. C., & Manzano-Santana, P. I. (2019). Effect of resin content and pressing temperature on banana pseudo-stem particle boards properties using full factorial design. Anais da Academia Brasileira de Ciências, 91(4), Article e20180302. https://doi.org/10.1590/0001-3765201920180302

Boon, J. G., Hashim, R., Sulaiman, O., Sugimoto, T., Sato, M., Salim, N., Amini, M. H. M., Izaida, I. N., & Fatimah, M. R. S. (2017).

Importance of lignin on the properties of binderless particleboard made from oil palm trunk. ARPN Journal of Engineering and Applied Sciences, 12(1), 33-40.

Börcsök, Z., & Pásztory, Z. (2021). The role of lignin in wood working processes using elevated temperatures: an abbreviated literature survey. European Journal of Wood and Wood Products, 79(3), 511-526. https://doi.org/10.1007/s00107-020-01637-3

Cecci, R. R. R., Passos, A. A., de Aguiar Neto, T. C., & Silva, L. A. (2019). Banana pseudostem fibers characterization and comparison with reported data on jute and sisal fibers. SN Applied Sciences, 2(1), Article 20. https://doi.org/10.1007/s42452-019-1790-8

Chen, M., Zheng, S., Wu, J., & Xu, J. (2023). Study on preparation of high-performance binderless board from Broussonetia papyrifera. Journal of Wood Science, 69(1), Article 17. https://doi.org/10.1186/s10086-023-02092-3

El-Kassas, A.M., & Mourad, A.H.I. (2013). Novel fibers preparation technique for manufacturing of rice straw based fiberboards and their characterization. Materials and Design, 50, 757-765. https://doi.org/10.1016/j.matdes.2013.03.057

EN 312. (2005) Particleboards-specifications. European Committee for Standardization.

Fahmy, T. Y. A., & Mobarak, F. (2013). Advanced binderless board-like green nanocomposites from undebarked cotton stalks and mechanism of self-bonding. Cellulose, 20(3), 1453-1457. https://doi.org/10.1007/s10570-013-9911-9

GB/T 4897-2015. (2015) Particleboard. Standards Press of China.

Hashim, R., Wan, W. N. A., Sulaiman, O., Sato, M., Hiziroglu, S., Kawamura, F., Sugimoto, T., Seng, T. G., & Tanaka, R. (2012). Properties of binderless particleboard panels manufactured from oil palm biomass. BioResources, 7(1), 1352-1365. https://doi.org/10.15376/biores.7.1.1352-1365

Homkhiew, C., Rawangwong, S., & Boonchouytan, W. (2016). Influence of wood species and thickness sizes on mechanical and physical properties of binderless particleboard. Ladkrabang Engineering Journal, 33(1), 18-23.

Homkhiew, C., Rawangwong, S., & Boonchouytan, W. (2021). Variation in mechanical, physical and thermal properties of binderless fiberboard influenced from long natural-fiber contents and types. UBU Engineering Journal, 14(2), 87-97.

Homkhiew, C., Rawangwong, S., Boonchouytan, W., Kaewpom, P., & Thongkaowphueak, T. (2017). Mechanical, physical and thermal properties of binderless fiberboard from rice husk flour and rice straw flour. The Journal of Industrial Technology, 13(3), 85-100.

Hubbe, M., Pizzi, A., Zhang, H., & Halis, R. (2018). Critical links governing performance of self-binding and natural binders for hot-pressed reconstituted lignocellulosic board without added formaldehyde: A review. BioResources, 13, 2049-2115. https://doi.org/10.15376/biores.13.1.Hubbe

Jamaludin, M. A., Bahari, S. A., Zakaria, M. N., & Saipolbahri, N. S. (2020). Influence of rice straw, bagasse, and their combination on the properties of binderless particleboard. Journal of the Korean Wood Science and Technology, 48(1), 22-31. https://doi.org/10.5658/wood.2020.48.1.22

Kurokochi, Y., & Sato, M. (2015a). Properties of binderless board made from rice straw: The morphological effect of particles. Industrial Crops and Products, 69, 55-59. https://doi.org/10.1016/j.indcrop.2015.01.044

Kurokochi, Y., & Sato, M. (2015b). Effect of surface structure, wax and silica on the properties of binderless board made from rice straw. Industrial Crops and Products, 77, 949-953. https://doi.org/10.1016/j.indcrop.2015.10.007

Kurokochi, Y., & Sato, M. (2020). Steam treatment to enhance rice straw binderless board focusing hemicellulose and cellulose decomposition products. Journal of Wood Science, 66. https://doi.org/10.1186/s10086-020-1855-8

Nadhari, W. N. A.W., Danish, M., Naris, M.S.R.M., & Geng, B. J. (2019). Mechanical properties and dimensional stability of particleboard fabricated from steam pre-treated banana trunk waste particles. Journal of Building Engineering, 26, Article 100848. https://doi.org/10.1016/j.jobe.2019.100848.

Nitu, I. P., Islam, M. N., Ashaduzzaman, M., Amin, M. K., & Shams, M. I. (2020). Optimization of processing parameters for the manufacturing of jute stick binderless particleboard. Journal of Wood Science, 66(1), Article 65. https://doi.org/10.1186/s10086-020-01913-z

Okuda, N., & Sato, M. (2004). Manufacture and mechanical properties of binderless boards from kenaf core. Journal of Wood Science, 5(1), 53-61. https://doi.org/10.1007/s10086-003-0528-8

Patel, B. Y., & Patel, H. K. (2022). Retting of banana pseudostem fibre using Bacillus strains to get excellent mechanical properties as biomaterial in textile and fiber industry. Heliyon, 8(9), Article e10652. https://doi.org/10.1016/j.heliyon.2022.e10652

Quintana, G., Velásquez, J., Betancourt, S., & Gañán, P. (2009). Binderless fiberboard from steam exploded banana bunch. Industrial Crops and Products, 29(1), 60-66. https://doi.org/10.1016/j.indcrop.2008.04.007

Shah, M. P., Reddy, G. V., Banerjee, R., Babu, P. R., & Kothari, I. L. (2005). Microbial degradation of banana waste under solid state bioprocessing using two lignocellulolytic fungi (Phylosticta spp. MPS-001 and Aspergillus spp. MPS-002). Process Biochemistry, 40(1), 445-451, https://doi.org/10.1016/j.procbio.2004.01.020

Shrestha, P., Sadiq, M. B., & Anal A. K. (2021). Development of antibacterial biocomposites reinforced with cellulose nanocrystals derived from banana pseudostem. Carbohydrate Polymer Technologies and Applications, 2, Article 100112. https://doi.org/10.1016/j.carpta.2021.100112

Sun, Y.-C., Lin, Z., Peng, W.-X., Yuan, T.-Q., Xu, F., Wu, Y.-Q., Yang, J., Wang, Y.-S., & Sun, R.-C. (2014). Chemical changes of raw materials and manufactured binderless boards during hot pressing: Lignin isolation and characterization. BioResources, 9(1), 1055-1071. https://doi.org/10.15376/biores.9.1.1055-1071

Suradmanee, T. (2018). Hazard of formaldehyde in office and residential buildings. EAU Heritage Journal Science and Technology, 12(2), 130-136.

Tajuddin, M., Ahmad, Z., & Ismail, H. (2016). A review of natural fibers and processing operations for the production of binderless boards. BioResources, 11(2), 5600-5617. https://doi.org/10.15376/biores.11.2.Tajuddin

Tay, C. C., Hamdan, S., & Osman, M. S. B. (2016). Properties of sago particleboards resinated with UF and PF resin. Advances in Materials Science and Engineering, 2016, Article 5323890. https://doi.org/10.1155/2016/5323890

The International Market Analysis Research and Consulting Group. (2023). Particle board market report by application (residential, commercial), sector (new construction, replacement), and region 2024-2032. https://www.imarcgroup.com/particle-board-market.

Vitrone, F., Ramos, D., Ferrando, F., & Salvadó, J. (2021). Binderless fiberboards for sustainable construction. Materials, production methods and applications. Journal of Building Engineering, 44, Article 102625. https://doi.org/10.1016/j.jobe.2021.102625

Zhang, D., Zhang, A., & Xue, L. (2015). A review of preparation of binderless fiberboards and its self-bonding mechanism. Wood Science and Technology, 49(4), 661-679. https://doi.org/10.1007/s00226-015-0728-6