RAPID PROTOTYPE FOR THE DEVELOPMENT OF SOUVENNIR PRODUCTS FROM BRONZE CRAFT

Authors

  • อุไรวรรณ คำภูแสน สาขาเทคโนโลยีอุตสาหกรรมการผลิต คณะเทคโนโลยีอุตสาหกรรม มหาวิทยาลัยราชภัฏพระนคร
  • นพพร บึกแว่น Department of Manufacturing Technology, Faculty of Industrial Technology, Pranakhon Rajabhat University, Bangkok , Thailand
  • รัฐพล สังคะสุข Department of Manufacturing Technology, Faculty of Industrial Technology, Pranakhon Rajabhat University, Bangkok , Thailand
  • สุขุมาล เหรียญทอง Department of Manufacturing Technology, Faculty of Industrial Technology, Pranakhon Rajabhat University, Bangkok , Thailand
  • ลักขณา ฤกษ์เกษม Department of Manufacturing Technology, Faculty of Industrial Technology, Pranakhon Rajabhat University, Bangkok , Thailand

Keywords:

Rapid Prototype, Souvenir, Bronze Craft

Abstract

This research develops products of souvenirs from the community of Bronze Craft. Using rapid prototyping methods.The objective of this research was to finding the parameters for rapid prototyping. The velocity of the test is 1000 mm / min. The force used to press the paper to the lack of 100 grams, which is the best value. Design and development of gift products from rapid prototyping. The results showed that the test piece 1 to 10 Measurement of workpiece 1 is an average of 19.57. The standard deviation is 0.16. The second is 159.38. The standard deviation is 0.47. The third is the average of 29.58. The standard deviation was 0.30, the fourth was 9.61, the standard deviation was 0.31, the fifth was the mean of 9.29, the standard deviation was 0.15, and the error of the headpiece of Buddha image The test results found that the error. The acceptable standard is not over plus and minus 0.5 millimeters, measured at 1,2,3,5,7,8,10. There are some places where the acceptable standard is not more than a positive and a negative value of 0.5 millimeters, which is 4,6,9 points. Most points of error are points on the top of the Buddha's head. There are overlapping stumps and are too small. As a result, paper cut and pouring of the workpiece can not reach the area.

References

Chua, C.K., Hong, K.H. & Ho, S.L. (1999). Rapid tooling technology. Vol., pages Part 1. A Comparative study, The international Journal of Advanced.

Eamsaeart K. (2554) Rapid tooling for Blow molding Process Department of Mechanical Engineering. Kasetsart University. Conference of Mechanical Engineering Network of Thailand (in Thai)

Griffith, M.L. et al. (1996). Freeform fabrication of metallic component using laser engineered net shaping (LENS), in proceedings of the Solid Freeform Fabrication Symposium, University of Texas at Austin.

Khaing, M., J. Fuh, & Lu, L. (2001). Direct metal laser sintering for rapid tooling processing and characterization of EOS parts. Journal of Materials Processing Technology. 113(1), 269-272.

Mazumder, J., Choi, J., Nagarathnam, K., Koch, J. & Hetzner, D. (1997). The Direct metal Deposition of H13 tool steel for 3D components. Journal of Materials Processing of the Solid Freeform Fabrication Symposium, University of
Texas at Austin.

Steenathbabu, A. & Karunakaran, K.P. (2006). Hybrid adaptive layer manufacturing An intelligent art of direct metal rapid tooling process. Robotics and computer Integrated Manufacturing. 22, 113-123.

Toshihide, H., Kirihara, S. & Miyamoto, Y. 92009). Freeform Fabrication of super alloy objects by 3D micro welding. Meterials and Design. 30, 1093-1097.

Vannitson K. (2554). Prototype of Rapid Tooling Machine by Laminated Object Manufacturing. Department of Mechanical Engineering. Kasetsart University. Conference of Mechanical Engineering Network of Thailand (in Thai)

Downloads

Published

2018-08-31

Issue

Vol. 14 No. 1 (2019): January-June 2019

Section

บทความวิจัย (Research Article)

License

โปรดกรอกเอกสารและลงนาม "หนังสือรับรองให้ตีพิมพ์บทความในวารสารวิจัยมหาวิทยาลัยราชภัฏพระนคร สาขาวิทยาศาสตร์และเทคโนโลยี" ก่อนการตีพิมพ์